Brake module BM3.
Brake module BM2.
Brake module BM1.
Dual occupancy detector LB101. The LB101 contains two independent occupancy detectors, each of which can be used to detect that a train or piece of rolling stock occupies a section of track. It operates on the “current sensing principle”. The LB100 only detect occupancy when there is a "current consumer" within the monitored track section (detection...
The DR5099 DigiNetHub is a double repeater where you can connect either four additional LocoNet devices and 4 X-Bus devices to your existing LocoNet and X-Bus devices. The 5 LocoNet and X-Bus connectors are completely separated from each other.
Energy storage system for locomotives. Suitable for all Doehler Hass decoders with SUSI interfaz.
Highly flexible 6-pole spiral cable.
Suitable for B-BUS. 1 meter length.
Suitable for L.NET / R-BUS / X-BUS connections. 6 meters length.
STP cable, suitable for DR4088 feedback modules of type S88-N. 5 meters length.
Connecor set for ECos (also used in other ESU devices). Includes 1 x 7-pin and 2 x 2-pin.
Manual: Digital for beginners, Part 1. This manual, edited by experts, answers the most important questions to the topic “How to digitize your own model railway layout“. Layout construction, programming and other functions are shown and explained here step by step. More to come soon!
Z21 booster, with 3A (track output). Adjustable track voltage via Z21® (12–24 V) RailCom® global detector (allows POM reading in the booster section) Configurable terminal loop feature with short-circuit detector Brake generator feature, configurable ■ Connections via CAN bus, B bus, CDE bus Configuration and update simply via app, PC with Z21® Please...
This point crossing interface can be used to make the output from the DR4024 servodecoder suitable for polarize turouts frogs.
STP cable, suitable for DR4088 feedback modules of type S88-N. 2 meters length.
The programming-adapter is the perfect complement to the D&H Programmer. It is directly connected to the Programmer and allows the update and sound uploading (for sound decoders) of any kind of D&H decoders.
Decoder programmer system for all D&H decoders. With this device and the corresponding softare (available to download from www.http://doehler-haass.de) it is possible to program decoders, record sounds, update firmware, etc. It requires USB cable
Set of three autofrog devices. The DCC80 Autofrog is a simple switch that automatically changes the frog polarity on your DCC layout. In most situations, the use of electrofrog points is recommended on digital layouts to ensure reliability but this can make extra switching more
The time control allows the use of our digital couplers with any decoder without time control function. One or two digital couplers can be connected to the time control. The time control can also be used for other products. After about 4 seconds the
The new ESU PowerPack Mini can be wired to all fourth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to
This decoder tester has been designed for testing decoders before these are installed into a loco. The Profi-Tester is simply hooked up to your digital central station, or the LokProgrammer. It comes with plug in for NEM652, NEM651, 21MTC, PluX22
To connect further input units (for example Lokmaus® 2/R3 / multiMAUS, (10760/10792/10810), turnout keyboard (10770), RouteControl (10772) or Rocomotion (10785). This distributor module can also be used as an extension of existing lines to units
STP cable, suitable for DR4088 feedback modules of type S88-N . 1 meter length.
The most well-known LokProgrammer unit, including power supply, serial PC cable, manual, software CD, USB adapter.
The cable is a replacement cable for the Lokmaus® 2/R3/multiMAUS (10760/10792/10810), turnout keyboard (10770) or RouteControl (10772). It cannot be used to extend connector cablees for Lokmaus® 1 (Item no. 10750).
Auto reverse loop module LK200 for DCC systems. With short circuit detection, enables the change of polarity automatically in reverse loops, turntables, etc. Easy-wiring installation, with only 4 wires to connect, and no additional control